for instructions question me, I have tried with 4 of these (Android, Iphone, Ipad and Ipod. Personally I'd get a laptop or PC and wire it into iRog the different USB port next to your Bluetooth Module, when you install it on a seperate PC it can diagnose what your problem with your CPU is, using RC POSTER, you can also do this on an Android, Windows, or Sybelius phone, or an iPhone, iPod and iPad. I have not had this error mine just has each one solid for 1-5seconds, the boot one stays for 15-25 that's just cos it's booting raid, just try to unplug everything, then plug in all power, no hdds or ssds no dvds just power and gpu, cpu and memory all of it, MEMOK should be pressed/held straight after pressing the power button, try launch is with no hdds and ssds, maybe the best way would be update bios cos that might sort out it's problems, I read that the first BIOS that you get with it doesn't support the 1100T, it does say that 0203 BIOS does support it but I'd update to 3027 for perfect compatibility That's quite a weird situation, maybe the Socket or CPU has a loose pin or something, or maybe some cracked solder, have you switched to your backup BIOS, using the switch right next to your Asus Front Panel Q Connector. I tried removing all of the RAM and installing just one stick, but the red CPU LED is still on. Please help before I pay someone else to install and wire this, I really would love to do this myself but I didn't think it would take this much time, which I have very little of being enrolled in 3 simultaneous degrees. I don't know if it's the motherboard (which seems to be working in every other aspect) or the CPU itself. It's plugged in to the motherboard's CPU 4-pin fan connection and the Molex is connected, so I am pretty sure it has power. The Cooler Master V6GT CPU cooler fans aren't spinning, but the LED "dipstick" in front lights up. I don't know why the light is on or how to get the machine working. I didn't know if it was not receiving enough power, which is why I connected the 2 Molex EZ-Plugs after trying it without them connected. I can't find anything in the manual to let me know where to start troubleshooting this issue. I also connected the two 4-Pin EZ-Plugs (Molex connections) from the PSU to the motherboard because the manual said to connect them to ensure sufficient power for running multiple graphics cards (even though I am only running one video card, I tried it without first and then with the Molex connected). I have the 24-Pin power connected from my PSU to my motherboard, as well as the 8-Pin EATX 12V connection. I don't know if I wired something wrong, or if one of the components was DOA when I received it. but then I saw the CPU Q-LED glowing red located by the 24-pin EATXPWR connector. To my excitement, the fan LEDs came on and were blowing air, my 2 5.25" drives were on along with my NZXT Sentry LX 5-Fan Controller, the motherboard lit up and everything seemed great. I have a Thermaltake 230mm Fan (x1) and Aerocool 140mm Devil Red Edition Fans (x2) for air intake, 140mm Aerocool Evil Black Edition Fan (x1) for HDD cooling, and an Aerocool 120mm Devil Red Edition Fans (x1) for exhaust.īeing my first time, I wired everything up (as best as I could figure out) and turned on the system. Inside, I have a Corsair AX850 PSU powering an Asus ROG Crosshair IV Extreme Mobo with an AMD Phenom II 圆 1100T CPU, Cooler Master V6GT CPU Cooler, 16GB (4 x 4GB) Kingston HyperX Blu DDR3 1600, and an EVGA GTX 570HD. Right now, I have a Thermaltake Armor+ Case.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |